Dating savage 340

The bolt can also be packed with grease, so clean and oil that, too. Gramps bought it new from a hardware store, and shot at most a box of shells. I load it, hand it to my friend, who shoulders the rifle, aims, and pulls the trigger. Rifle does not fire.

Stevens / Savage Bolt Ac

Oops, he did not take the safety off. After unloading, I was able to reproduce the AD every time.

When safety was set to "Fire", the complex trigger sear was back enough to release striker. After cleaning trigger mechanism and bolt, and proper light oiling, the safety works as expected; no fire on "Safe", and rotating safety to "Fire" does not drop striker.

Maybe it was due to difference in design, or quantity of grease. Thanks to all for the info. Yes,I have taken the action out and cleaned thoroughly. Better to err on the side of caution. The rifle is a bulky sort with its oversize walnut stock and all,but its a decent rifle for the money I have into it and I like it.

I'm partial to old time workmanship.

Dating savage 340. Savage Feeding Problem

The little Hornet is fun and cheap to shoot. Yeah, If I found one in 22 hornet, I would jump on it. Saw one on here a while back in which tempted me. Was going to use it as a youth rifle to loan to nieces and nephews but the AD issue kind of freaked me out and I don't really want anyone else using it. Since I cleaned it good, I haven't been able to replicate the issue, but it is always kind of in the back of my mind if you know what I mean. Originally Posted by cv I reload - I have often thought what sleek little rifle they would be if all the extra wood was removed. As is, they remind me of the old Mossberg bolt action shotguns.

The hardest part is finding a big buck. The easiest part is getting "em" out. Print Thread Switch to Threaded Mode.

3 Suggested Answers

For front sights that use a screwed on ramp type base, a special sight pusher tool should be used that pushes the sight by cranking a screw in. In the LH photo below you see the original stock finish. The barrel is slid into a metal recoil lug that abutted against the receiver front, being held in place by a barrel nut.

The front action screw was threaded into the bottom of this recoil lug. The rear trigger guard wood screw was simply there to hold the rear of the trigger guard and was only screwed into the stock. The front barrel band screw screwed into a block that was attached to a thin sheet metal band around the barrel in the forward part of the forearm. If someone drills and taps these rifles for the later scope mounts, there will usually be no model or caliber designation showing as the scope base covers the markings up.

Savage Love Episode 340

This gun was made with many metal stampings which set the guide for the design for the later to come Savage model The barrel was threaded and chambered, then threaded into the receiver, rotating in until it properly headspaced, then being locked in place by the barrel nut. This process greatly reduced skilled labor in manufacturing AND the assembly.

Neither of the model or versions had provisions for a installing telescope sight mount. However the C shows up with being drilled and tapped for a peep sight. In the photos below you can see the wrapped around "C" extractor, which has a small hook on the RH side and a rounded rear section that holds the case rim in place until the ejector pushes it out at the rearward stroke through the groove you see on the lower RH side of the bolt.

The LH photo below is of the , where the RH photo shows the model in 22 Hornet which is very similar, but fits a smaller diameter bolt face. You will notice the ejector slot in the lower RH bolt face of both. The initial model utilized a rather different style ejector than commonly seen on most later guns, being a long sheet metal unit running from the front of the receiver back along side of the magazine well to the rear of the magazine area. The later models A, B and C used what would later became standard, was a smaller short wire spring-loaded pivoting ejector in the LH receiver at the rear of the magazine area.

In the photo below the LH side shows the single long spring ejector. This ejector also incorporated the front magazine guide and uses the regular guide hole as it's retainer. The center photo shows at the top the , being the longest case center a and at the bottom the 22 hornet.

What were the manufacturing dates savage 340B 222 rifle

Some of the later models, the D in and the used a total different design, being a small dia. The extractors for these plunger type ejector bolts used small captivated spring loaded extractors, these being the forerunner of the current model type extractors. The C had numerous small changes in the trigger unit the shape of the housing, different sear and sear lever , the top gas shield was also changed. This clip was captivated when the striker unit when assembled into the bolt body as seen in the photo below. Also the round blind hole on the rear base of the bolt handle was what the safety locked into securing the bolt when on safe.

Categories

The models A, B, C and S were 22 Hornet caliber only and produced from to running parallel with the model This smaller caliber rifle used the same receiver as the , but it sported a shorter ejection port, and they cut a smaller hole in the bottom for assorted magazine fittings to accommodate the smaller caliber, existing model 23D rifle magazine.

Over the years, I have seen a few of these rifles with this shotgun style magazine, where somehow they managed to stay with the rifle over the years but was not sure as to the origin.

As mentioned above, the model and thru the C guns were made for the modified shotgun magazines, which apparently had a deeper stop pad that the later magazines. When installing new later or current replacement magazines, remember they are made on different factory tooling.

The receiver has recesses which act as a upper stop for the magazine, but the stop pad is taller on the new magazines. You may have to lightly file off the stop pads on the new magazines. These are the tabs that are protruding both front and rear corners of the magazine body. Not much is needed to be removed, about. Otherwise the magazine will not go all the way up and it usually will get bound up by being twisted front to back and get bound against the front and rear guides. Also for the model only, not the A, B, or C series you also need to do one more alteration.

On the top LH front follower retainer dimple, you need to make about 2 passes with a file from the inner top to inward at a 45 degree angle, just breaking the sharp edge. You will need to press the follower down a bit or remove it when doing this. If you don't file this off, it may be hard to open the bolt after closing and it will swell the front sides of the magazine out a bit.

What is happening is that the early long ejector rides up into the slot in the bolt, and you have now forced it into the magazine opening. You may luck out if using older or used magazine that may be worn here enough to not bind. In the LR photo below, you can see the filed off shiny spot on the forward inside follower stop dimple.

Enter the Savage From all information available, t he mother company Savage, dropped the Stevens model C at the end of and picked up the same basic design in , producing it under the renamed Savage model which remained in production until In all of the factory advertisement, very little was mentioned as to model suffix letters unless it was for the "S" Deluxe or the "V" Varmiter. The suffix model numbers for the model series did not match with the previous model series, but started over as it appears the initial model would have probably have been basically the older model C with the design and caliber changes.

These suffix letters are a letter added to the model number on these guns when a design change was implemented, starting with A, and ending with E. Therefore it appears that each time the factory made a significant change in the firearm, a suffix letter was added to the model number. That could be partly why when we who are trying to re-create the history many years later, we are running into many unanswered questions.


  • Add Your Answer;
  • Savage 340 in 222;
  • Savage Model 340 30/30 Bolt Action.
  • military dating sites uk?
  • .
  • university dating site canada.
  • hot guy dating an ugly girl!

Also, I have found numerous transition carryover of parts between the series, and this would be common in the industry when using up existing older parts inventory. And suffix model letters were only important in the spare parts department, or later gunsmiths needing parts something the sales department was oblivious of. With the introduction of the , the bolt handle was changed to the more common round knob type.

The handle's attachment to the rear bolt body was changed s omewhere during production of the bolt handle being pressed onto a horizontally knurled rear bolt body was apparently later changed to being silver soldered on OR a good gunsmithing repair on one that I saw.